To make a homemade dog snuffle mat you will need:

An Old T-shirt and/or jumper (A jumper or polo shirt is best as some t-shirts can be a little too stretchy)A pair of Scissors STEP 1First, cut a large rectangle from your t-shirt or jumper. This will form the base of your snuffle mat. If you have both a thicker jumper material and a t-shirt, it’s best to use the thicker material for the base. You can make your snuffle mat any size you like, but around 25 cm by 35 cm is a good size to start with. STEP 2Next, snip a row of small holes along the length of the material, leaving about 1 cm between each hole. Repeat this step until you have around 8 rows of holes, leaving a few centimetres of space between each row. STEP 3Now you need to cut lots of strips of material to tie onto your mat. The strips should be about 20 – 25 cm in length, and about 3-4 cm wide. Get creative with your colours! STEP 4When those are done, decide which side of your base you want to face upwards. Once you’ve decided, take a strip of material, and thread it through the back of the first and second hole of the first row. Flip the mat over and tie the strip into a double knot around the front. Repeat this until all of the holes are filled. STEP 5Your DIY snuffle mat is ready! When you’re ready to feed your dog, simply hide a portion of their daily food allowance in the folds of the mat and then place it on the floor for them to investigate. It’s best to stick to dry food as wet food could get messy!

To make a DIY ring ragger dog toy you will need:

A pair of scissors.An old jumper - we recycle old Battersea uniforms to cut down on waste. STEP 1Start by cutting the cuff off the jumper. This will form the base of the toy. If you have a bigger dog, you can make the ring ragger bigger by using the neck or bottom of the jumper, instead of the sleeve cuff. STEP 2Next, cut one long strip of material from the rest of the jumper. Make this piece as long as you can to make sure it will go all the way around your jumper cuff. STEP 3Tie the long strip onto the cuff, at the middle of the strip, making sure you have an even amount of material on each side of the knot. STEP 4Take your strip on the left hand side and pass it around the front of your cuff and over to the other side to make an 'L' shape. Then take the strip on the opposite side and pass it over your first strip, and around the back of the cuff, passing it through the loop that you have made with the strip on the left (this part is a little tricky, so you way want to check out our video). Pull both strips as tight as you can, trying to cover the material underneath. STEP 5Repeat the last step, but this time start your knot on the opposite side. So this time, you will be making a backwards 'L' shape with the strip on the right hand side. STEP 6Keep repeating this process, alternating sides each time, until you have gone all the way around the cuff. You may sometimes need to shuffle the knot upwards to overlap with the previous knot and keep the material underneath covered. Tie to finish and then cut off any excess material.

To make a DIY octopus dog ragger toy you will need:

An old tennis ballA pair of scissorsAn old t-shirt or jumper - You’ll want to make sure it’s quite a sturdy material so that your dog can’t rip it up too easily. We recycle old Battersea uniforms. STEP 1Start by cutting off the seam along the bottom of your jumper or your t-shirt. Cut this seam into two equal strips and put these to the side for later. STEP 2Cut a large rectangle about 25 cm by 35 cm from your T-shirt or jumper. Place your tennis ball in the middle of the edge closest to you and roll it up tightly in the material. STEP 3Use one of the strips that you cut earlier to secure the tennis ball into place with a knot. Tie four knots, on alternating sides, until you’re happy the tennis ball is properly secured. Repeat this on the other side, and then cut off any excess strips of material. STEP 4Next, cut the material at either end of the tennis ball into 6 strips. This will allow you to create two plaits at either end. STEP 5Using three strips at a time, tie your plaits, making sure to leave yourself enough material to tie them up at the end. Repeat this on both ends. Check your toy over for any loose material and then it’s play time!